LAP18EULBALAP18EULFRNOTEBOOK CART ASSEMBLYWITH TIMERAssembly Instructions for:INTERIOR E-UNITREPOSITIONING / REPLACEMENTANDTIMER REPLACEMENTPart
Step 4Reinstall the 8 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracke
Step 6Reinstall the E-Units (set aside from being removed from the rear) as follows:1. Rotate the E-Unit 180 degrees (from original position).2. Cross
E-UNIT REPLACEMENT:'REAR LOCATION'NOTE:UNPLUG CART (TIMER) POWER CORD FROMPOWER SOURCE BEFORE STARTINGStep 1Remove 16 screws (2 per shelf)
Step 2With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mountingtabs) shown in Detail 'B',
DETAIL 'C' DETAIL 'D'Step 3Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart int
Step 4Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top.When repositioned correctly,
Step 5Reinstall the 8 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracke
Step 1Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the powercord of the E-Unit(s) from the t
clipDETAIL 'A' DETAIL 'B'bracketassemblybracketassemblyStep 2Remove E-Unit(s) by griping the top and tilt it side ways until it cl
Step 3Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top.When repositioned correct
clipDETAIL 'A' DETAIL 'B'E-Unit powercordtimer assemblybottom shelfFront Viewbracketassemblybracketassembly
TIMER REPLACEMENT:'E-UNIT AT REAR LOCATION'NOTE:UNPLUG CART (TIMER) POWER CORD FROMPOWER SOURCE BEFORE STARTINGDETAIL 'A'Step 1R
Step 2With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf frommounting tabs) shown in Detail &apo
Step 3Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly.bottom flange-timer/bracketStep 4Remov
Step 5Install replacement timer with 2 screws. Adjust timer dial to current time. If necessary, adjust timercharging times to match the original tim
Step 7Reinstall the 3 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracke
TIMER REPLACEMENT:'E-UNIT AT FRONT LOCATION'NOTE:UNPLUG CART (TIMER) POWER CORD FROMPOWER SOURCE BEFORE STARTINGStep 1Open both front door
clipDETAIL 'A' DETAIL 'B'bracketassemblybracketassemblyStep 2Remove front-left E-Unit by griping the top and tilt it side ways unt
DETAIL 'A'Step 3Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A').DETAIL &a
Step 4With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf frommounting tabs) shown in Detail &apo
Step 6Remove 2 screws that secure timer to bracket.Step 7Install replacement timer with 2 screws. Adjust timer dial to current time. If necessary, a
Step 2Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interiorshelf channel and set it asi
bottom flange-timer/bracketStep 8Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord fromthe time
DETAIL 'C'Step 10Reinstall 6 screws to rear panel that will secure the 3 interior shelves(see DETAIL 'C'). DO NOT OVER TIGHTEN SC
E-Unit at rear$8;$8;$8;$8;$8; $8;LABEL INSTALLATION:E-Unit at frontsuggested labe
Part #031-6565Rev. 08.29.05 CHPAD LOCK - DOOR:Open Lock The First Time1) Set the combination to 0-0-0-02) Depress shackle and pull open.To Set You
DETAIL 'D'Step 4Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D',t
Step 5Reinstall the E-Units (set aside from being removed from the front) as follows:1. Rotate the E-Unit 180 degrees (from original position).2. Cros
Step 6Reinstall the 8 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracke
Step 1Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DETAIL 'A').DETAIL 'A'E-UNIT REPOSITI
Step 2With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mountingtabs) shown in Detail 'B',
DETAIL 'D' DETAIL 'E'Step 3Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the c
Komentarze do niniejszej Instrukcji